联系我们
名称：直流稳压电源诚信厂
电话：xxx
手机：xxx
邮箱：xxx
地址：xxx
新闻动态
直流稳压电源注意事项
直流稳压电源注意事项
Notes for DC Voltage Regulated Power Supply
1.为防止漏磁干扰,稳压器与使用设备之间放置距离不应少于2米.各种磁性记录,碟,卡等应远离本机2米之外，以防意外磁化. 2.稳压器一般包括输入端子(A,B,C),输出端子(a,b,c,n),屏蔽,铁芯壳接地端子.这些端子在稳压系统已正确联接. 3.如负载不平衡度超过20%时在轻载的一相并联一个电阻性负载使之平衡.同样,如果输入端的线电压的不平衡度大于10%时也会影响本机的稳压性能,这时也应从输入端设置单相调压器使输入端的线电压基本平衡.输入电压及负荷两平衡度不超过上述范围,输出线电压不平衡≤5%. 4.当负载设备有短路时,用户需关机检查,消除短路故障后再另行开机. 5.连续工作时间较长时,机器有一定的温升,其指示值会稍为下降,略低于实际电压值. 6.应放在通风较好的位置,若通风条件较差的,请在室内装上换气扇。
1. In order to prevent magnetic leakage interference, the distance between the regulator and the equipment should not be less than 2 meters. All kinds of magnetic records, discs and cards should be far away from the local machine 2 meters in order to prevent accidental magnetization. 2. The regulator generally includes input terminals (A, B, C), output terminals (a, b, c, n), shielding, iron core shell grounding terminals. These terminals have been correctly connected in the voltage stabilization system. 3. If the unbalance of load exceeds 20%, a resistive load is connected in parallel with the light load to balance it. Similarly, if the unbalance of line voltage at the input end is greater than 10%, the voltage stabilization performance of the unit will also be affected. At this time, a single-phase voltage regulator should be installed at the input end to basically balance the line voltage at the input end. Both input voltage and load are balanced. When the load equipment is short-circuit, the user needs to shut down the machine for checking, eliminate the short-circuit fault and start the machine separately. 5. When the continuous working time is long, the machine has a certain temperature rise, and its indication value will drop slightly, slightly lower than the actual voltage value. 6. It should be placed in a better ventilated position, if ventilated. If the condition is poor, please install ventilator in the room.
Notes for DC Voltage Regulated Power Supply
1.为防止漏磁干扰,稳压器与使用设备之间放置距离不应少于2米.各种磁性记录,碟,卡等应远离本机2米之外，以防意外磁化. 2.稳压器一般包括输入端子(A,B,C),输出端子(a,b,c,n),屏蔽,铁芯壳接地端子.这些端子在稳压系统已正确联接. 3.如负载不平衡度超过20%时在轻载的一相并联一个电阻性负载使之平衡.同样,如果输入端的线电压的不平衡度大于10%时也会影响本机的稳压性能,这时也应从输入端设置单相调压器使输入端的线电压基本平衡.输入电压及负荷两平衡度不超过上述范围,输出线电压不平衡≤5%. 4.当负载设备有短路时,用户需关机检查,消除短路故障后再另行开机. 5.连续工作时间较长时,机器有一定的温升,其指示值会稍为下降,略低于实际电压值. 6.应放在通风较好的位置,若通风条件较差的,请在室内装上换气扇。
1. In order to prevent magnetic leakage interference, the distance between the regulator and the equipment should not be less than 2 meters. All kinds of magnetic records, discs and cards should be far away from the local machine 2 meters in order to prevent accidental magnetization. 2. The regulator generally includes input terminals (A, B, C), output terminals (a, b, c, n), shielding, iron core shell grounding terminals. These terminals have been correctly connected in the voltage stabilization system. 3. If the unbalance of load exceeds 20%, a resistive load is connected in parallel with the light load to balance it. Similarly, if the unbalance of line voltage at the input end is greater than 10%, the voltage stabilization performance of the unit will also be affected. At this time, a single-phase voltage regulator should be installed at the input end to basically balance the line voltage at the input end. Both input voltage and load are balanced. When the load equipment is short-circuit, the user needs to shut down the machine for checking, eliminate the short-circuit fault and start the machine separately. 5. When the continuous working time is long, the machine has a certain temperature rise, and its indication value will drop slightly, slightly lower than the actual voltage value. 6. It should be placed in a better ventilated position, if ventilated. If the condition is poor, please install ventilator in the room.
